Haltech’s Advanced Torque Management – More Grip, Less Slip!

mainpromoimage_web

Aimed at drag racing professionals, Advanced Torque Management is Haltech’s brand new engine management feature that promises to reduce the loss of traction and tyre shake, making aborted passes a thing of the past.

article_atm02

Haltech’s Advanced Torque Management eliminates the impact numerous variables like the surface condition or temperature can have on the car’s performance providing consistent, repeatable results.

article_atm04

How does it work?

A Driveshaft RPM sensor monitors the Driveshaft RPM and reports back to the ECU. The Driveshaft RPM is then used as a target in the Torque Management tables. If the Driveshaft RPM goes above or below the target Driveshaft RPM, the ECU immediately adjusts the tune to compensate and bring the Driveshaft RPM back to its pre-set target.

atm_graph01

As well as Driveshaft RPM, Haltech’s Advanced Torque Management can also be mapped against Wheel Speed or Engine RPM. Multiple profiles can be set up and triggered by a sensor input or a dashboard switch panel.

How does it help you go faster?

The benefits of having full control over your torque are many and varied, the most obvious one being consistency. Changing track conditions, temperature or environmental factors can all cause loss of traction often resulting in aborted runs.

article_atm01

With Haltech’s Advanced Torque Management every run counts and every run delivers consistent results. If there is one thing all seasoned drag racing pros agree on it’s that consistency equals lower ETs.

How to get Haltech Advanced Torque Management?

Haltech Advanced Torque Management is available on the following products:
• Elite 2500T
• Elite 2500 (with a 2500T upgrade)
• REM (Race Expansion Module)

atm_graph02

For more information contact:
 @
or call: 760 598 1941 (Nth America) or +61 2 9729 0999 (Australia, Europe, Asia and Africa)


2500t_web

Elite 2500T (DBW + Advanced Torque Management)

Applications:
• 1 to 12 cylinder engines
• 1 to 4 rotor engines
• Normally aspirated or forced induction

Features:
• Waterproof Case (IP67)
• Torque Management Functionality
• 8 x Fuel Injection Outputs
• 8 x Ignition Outputs
• 28 x Digital Outputs
• 10 x Analogue Voltage Inputs
• USB Laptop Communications up to 1 MB/s
• 6 x Engine Position Inputs with extensive trigger type support
• Programmable Injector Peak and Hold Currents
• OBDII Capable – Set and clear diagnostic trouble codes, view live engine data
• ESP Calibration Software – Intuitive and easy to use
• Dual CAN Bus communication for OEM and Haltech CAN Expansion
• User definable 5D Tuning – Tune by gear, Cam angle or any channel for ultimate flexibility
• Variable cam control – Independently control up to 4 camshafts Auto tune capabilities –
• Short and Long term fuel, ignition, boost and idle control learning
• Dual Channel Knock Control – with high speed digital filtering for accurate detection
• Multi-fuel Support – Support for Petrol (Gasoline),LPG, Methanol and Ethanol
• E85 Flex Fuel Ready – Direct connection to sensor.
• Closed Loop Boost Control – Multiple Modes – Tune by gear, wheel speed or time
• Closed Loop Idle Control – With learning for consistent idle stability
• Closed Loop 02 Control – Dual bank control for precise tuning
• Anti-Lag and Launch Control – Drag and Rally modes
• Data logging – Up to 40 channels of logging. Sampling rates up to 5ms
• Multi Level Engine Protection – Set limits for sensors and protect your engine
• ECU comes fully enabled, no additional charges for advanced features

Outputs:
• 8 x Current controlled injector drivers
• High or Low impedance injector compatible
• Programable Peak Current – 0A – 8A
• Programable Hold Current – 0A – 2A
• All spare injector outputs can be used as generic DPO’s with 1A Max output.
• 8 x Over current protected ignition drivers
• All spare ignition outputs can be used as generic DPO’s with 1A Max output.
• 5 x Over current protected low side pulsed outputs
• 1 x Dedicated engine control relay output which can control up to 6 relays simultaneously
• 2 x Over current protected hi / low side motor outputs
• Suits most OEM throttle bodies and pedals
• 1 x 4 wire stepper motor control
• Can be configured as 4 x hi / low side outputs

Inputs:
• 10 x Analogue Voltage Inputs
• 2 x Engine Position Inputs with extensive trigger type support
• Supports variable reluctor and digital inputs
• 3 Bar Internal MAP Sensor rated up to 200kPa of Boost (2bar/29psi)
• 2 x CAN Bus communication for Haltech CAN and Vehicle CAN Expansion
• 1 x USB Connection for Programming
• On-board Data Logging
• Fastest Sample Rate 5ms
• 2MB Internal Storage

Pricing:
Australia RRP:  AUD$4449.00 inc GST
North America MSRP: USD$3495.00


rem_web

REM (Race Expansion Module)
The Race Expansion Module (REM) is used in conjunction with the Haltech Elite 2500 ECU to offer extra Input and Output functionally as well as Advanced Torque Management. Using the REM with the Elite 2500 allows sequential staged injection of up to 16 injectors, and will drive up to 32 injectors.

The REM also has additional Analogue and Digital inputs which can be used for data acquisition as well as additional Digital outputs.

Features:
• Advanced Torque Management
• 8 x Fuel Injection Outputs
• I/O Expansion (Available when not using I/O Expander 12)
• Waterproof Case

Inputs/outputs:
• 8 x Fuel Injection Outputs
• 4 x Digital Pulsed Outputs
• 4 x Digital Pulsed Outputs
• 4 x Digital Pulsed Inputs
• 8 x Analogue Voltage Inputs (with selectable Pull up)
• 2 x Buffered Analogue Voltage Inputs suitable for O2 Sensors
• 1 x Haltech CAN Connection
• 2 x System Synchronisation Pulsed Inputs
• 1 x System Synchronisation Watchdog Output
• 1 x Injection Relay Control Output
1 x 8VDC Injection Relay Conditioning Circuit Supply

Pricing:
Australia RRP:  AUD$3295.00 inc GST
North America MSRP: USD$2495.00